PTFE/FEP/PFA Teflon Heat Shrink Tubing
PTFE/FEP/PFA Teflon Heat Shrink Tubing is built from Fluoropolymer (PTFE/FEP/PFA). It ships expanded and recovers to a tight, conforming fit once you apply heat (hot-air gun, 150–250 °C). On the shelf it is held to shrink ratio 1.1:1 ~ 4:1, working range -65℃~+260℃. Buyers spec it for Chemical piping, semiconductor and medical tubing — the typical call is a sized part that stays put through vibration, thermal cycling and field handling. Below is the spec table, the size matrix we keep in stock, and the selection notes our engineering team uses when a purchaser sends a cable or component drawing.
Specification
| Material | Fluoropolymer (PTFE/FEP/PFA) |
|---|---|
| Operating temperature | -65℃~+260℃ |
| Shrink ratio | 1.1:1 ~ 4:1 |
| Wall type | Thin wall / standard |
| Colors | Transparent / natural |
| Standards | UL94 V0, MIL-I-23053 |
| Note | PTFE(1:1), FEP(1.3:1), PFA(4:1); best chemical resistance |
What it is and how it recovers
PTFE/FEP/PFA Teflon Heat Shrink Tubing starts as an expanded tube. The expansion is locked in by cross-linking, so it holds the large diameter until heat is applied and it recovers toward its extruded size. With a 1.1:1 ~ 4:1 ratio you can recover a sleeve roughly 1.1× the recovered diameter, covering both a bare conductor and a bulky connector in one pass. Because the body is Fluoropolymer (PTFE/FEP/PFA), the recovered wall keeps its dielectric strength and mechanical protection after cooling — it does not relax back. For procurement this matters: the part you receive is reusable on the bench, but once installed it stays put for the life of the assembly.
Where PTFE/FEP/PFA Teflon Heat Shrink Tubing is used
Primary applications: Chemical piping, semiconductor and medical tubing.
How to select the right size
Specifying PTFE/FEP/PFA Teflon Heat Shrink Tubing is mostly about matching three numbers to the part you are covering:
- Recovered vs. supplied diameter. Pick the supplied (expanded) ID at least 1.1× the object's largest diameter so the sleeve slides on, then confirm the recovered ID grips it. When in doubt, size up one step rather than forcing a tight fit.
- Temperature class. The continuous range is -65℃~+260℃. If the assembly sees brief excursions beyond that, tell us — we will flag a high-temp grade instead of letting the wall soften in service.
- Wall and adhesive. Thin wall for tight harness bundles; medium/thick wall or adhesive-lined (dual-wall) where you need environmental sealing or abrasion resistance. We keep both in stock.
Frequently asked questions
What shrink ratio should I choose for PTFE/FEP/PFA Teflon Heat Shrink Tubing?
If the connector or lug is only slightly larger than the wire, a 2:1 ratio is enough. When one sleeve must cover both a bare conductor and a bulky barrel, ask for 3:1 or 4:1 (we stock 1.1:1 ~ 4:1). The rule is: supplied ID ≥ ratio × largest object OD.
Can PTFE/FEP/PFA Teflon Heat Shrink Tubing be used outdoors / buried?
Single-wall polyolefin is fine for indoor harness protection. For outdoor, buried or wet locations specify the adhesive-lined (dual-wall) version — the melt adhesive seals out moisture and resists tracking. Tell us the environment and we point you to the right wall type.
What is the temperature limit of PTFE/FEP/PFA Teflon Heat Shrink Tubing?
Continuous operating range is -65℃~+260℃. Brief excursions above that are possible with the right grade; for sustained high heat we recommend the silicone-fiberglass or fluoropolymer family instead.
Request a quote for PTFE/FEP/PFA Teflon Heat Shrink Tubing
Tell us the inner diameter, wall type, length and quantity you need, plus the voltage class and environment. We return a sized part number, stock status and lead time — no price guessing, no minimum-order surprises.
Certifications & Compliance
PTFE/FEP/PFA Teflon Heat Shrink Tubing is built to the following standards and directives. Certificates are supplied per batch on request.
- UL94 V0
- MIL-I-23053
Tell us your target market (EU / US / Asia) and we align the documentation to your filing.
Size range & specification notes
PTFE(1:1), FEP(1.3:1), PFA(4:1)；耐化学性最优